How to polish a knife at home to a mirror shine: all kinds of polishing methods

The properties and characteristics of a high-quality knife directly depend on the level of its final grinding and polishing. They have a great influence not only on the ability to maintain the integrity of the cutting edge and sharpening for a long period of time, but also on the productivity of operation - minimum effort, maximum result. Also, of course, all this is imprinted on the appearance of the entire knife and guarantees additional resistance to corrosion. It is precisely the precise adherence to technical subtleties and the quality of these processes that allows us to answer a simple question, which is why some knives cut better than others and do not become dull an order of magnitude longer.

Handmade knife polishing.

Difference between grinding and polishing

To understand the difference between the process of grinding and polishing, you should refer to the very definitions of these actions. Let's look at them in more detail:

Grinding

Using abrasives of various sizes, it allows you to make the surface of hard material smooth.

Polishing

The final stage in blade grinding, with its help you can achieve extreme smoothing of the surface until a specific shine appears.

The concepts are actually the same in the workflow. And they follow sequentially depending on the need. Bringing the workpiece to the required size, as well as adjusting its shape or removing rust, will require grinding.

It is used if necessary and is the final stage of grinding. If the task is to bring the surface to a shiny state, then you should resort to polishing.

It can be done manually or using special wheels on an angle grinder or machine.

This is where the opinions of the masters differ greatly. With the help of special machine devices, the process will take much less time. But according to experts, the result will be weaker than polishing by hand.

Steel polishing and knife sharpening

Polishing metal surfaces

is perhaps the most intensive work process in knife production - only consistent execution of certain work can lead to a good result.

Abrasive sandpaper and sanding paper are available for sale.

ZM, VSM and Klingspor,
have proven themselves best These types of abrasive paper have a high-quality bond of abrasive grain, which means that the grain is firmly connected to the supporting material and stays on it for a long time, in addition, the grain is evenly distributed over the entire area of ​​the material. Using low-quality materials will require more processing time and, moreover, will not bring the desired result - this is not the case when you need to save.

For coarser sanding work, sandpaper with grits of 60, 80, 120, 180 and 240 is suitable.

To obtain a smoother surface, it is better to use 600, 800, 1000, 1200 and 2000 grit wet sanding paper.

These numbers indicate how many abrasive grains are located per square inch of the carrier material - the higher the number, the thinner the sandpaper.

When grinding metal surfaces, experience plays a major role. Only the basics of this process can be outlined on paper, but even here the main rule remains: theory is theory, and experience is acquired with practice.

Not every grade of steel lends itself equally well to grinding.

For example, RWL34 steel presents fewer grinding problems than ATS34, although the former has a higher carbide content. In terms of wear of sanding paper, the absolute superiority belongs to steel CPM-S30-V and CPM-S90-M (formerly CPM440-V and CPM420-V), but subsequently they hold an edge better.

At the workplace, sheets of sanding paper must be distributed according to the grit size. It is very important to have good lighting in the workshop (halogen lamps are best) - only with such lighting can you determine whether the traces of previous processing have been completely removed and switch to paper with a finer grain.

As sanding aids, there are different shaped pads that not only spare your fingers, but also allow you to achieve truly smooth surfaces.

The choice of paper grit for the initial sanding phase depends on the quality of the surface obtained as a result of its preliminary processing.

If the surface was sharpened with a file, then it is better to start with 80 or 120 grit paper. After processing the blade on a sanding belt with 120 grit, you can switch to 240 grit for further sanding. Some craftsmen grind and polish the material to the very end on a machine. As you can see, the range of surface treatment options is quite wide.

But let's return to the blade, the surface of which was processed with a file. As a rule, the file moves across the blade, so in order to remove all the grooves left by the file, you should grind along the blade. To do this, you need to use a sanding block to which you can press the sanding paper firmly and evenly. Once the surface has been sanded with 120 grit paper, you can move on to a finer grit, preferably 240, and make movements perpendicular to the direction of movements during the previous sanding. When moving from one grain size to another, the difference between its values ​​should not be too large, but not very small either.

In practice, this sequence has proven itself: 120, 240, 400, 600, 800, 1200 and 2000; or 180, 320, 600, 800, 1200 and 2000.

To obtain a gloss finish, you can finish the treatment with 600 grit. When changing the grit, it is very important to also change the direction of movement of the abrasive material, which allows you to determine whether the traces of the previous grinding have been removed.

During the grinding process, do not forget about the spine of the blade, the appearance of which should correspond to the entire product as a whole. Much attention should be paid to the edges and transition areas - they must be sanded clean and to sharp corners, which is not so easy. On the finished knife, these places can be used to judge the quality of the work performed.

Now the question arises: gloss or mirror shine?

To obtain both surfaces, painstaking pre-treatment is necessary.

A glossy surface is obtained if, at the end of processing, the sanding paper moves across the surface in a straight line and evenly, and the paper should completely cover the surface.

A hard rubber pad is a good aid here, but when sanding transition areas, be careful not to round off the corners. What grain size to finish processing with is a matter of taste.

A beautiful surface is achieved with 600 grit, but you can also combine, for example, start with 400 and immediately move to 1200 for final sanding. Some craftsmen use additional grinding paste or matting agent.

To polish the surface to a mirror shine,

it is necessary to pre-grind it with paper with a grain size of up to 2000. Only after this can you begin polishing on a polishing machine using a soft polishing wheel. Polishing paste, available for sale in specialized stores, is suitable as a polishing agent.

When polishing, do not apply much force to the edges so that sharp corners do not round off, which can easily happen if the master is overzealous. The main thing is a clean surface without any remaining abrasive grain: if the grain gets into the polishing wheel, the entire polishing can go down the drain. A blade polished to a mirror shine requires painstaking work, but often all the beauty of this shine quickly disappears. A highly polished surface on blades made from carbon steel is an effective protection against corrosion, but for chrome steel such protection is no longer necessary.

Finally, one more question: to what grit size should you grind before hardening the metal? It depends on the steel itself and the hardening method.

On stainless steels, which are hardened in vacuum furnaces, no scale layer is formed, so there are no restrictions on the degree of grain size during grinding; moreover, everything that can be done with the surface of unhardened steel can be easily done manually. If the blade should have a normal gloss, then the surface before hardening can, in principle, be completely polished, but after hardening, minor refinement is necessary. If we are talking about a mirror finish, then finish grinding before hardening with 1200 grit and continue grinding after hardening. As a rule, the method of hardening carbon steels is different from that of stainless steels, for example, in a forge, while they form a layer of scale. Therefore, there is no point in subjecting the surface to final processing before hardening. In such cases, sanding should be completed with 400 grit and continued after hardening.

Anyone who prefers to work with “their” steel can, over time, develop their own individual processing methods that are best suited for this particular type of steel.
Sharpening a knife
A new blade should be sharpened only after it has been hardened. This means that when making a blade it is necessary to leave 0.2-0.6 mm for the future blade. If the blade is finally sharpened before hardening, then as a result of exposure to high temperatures during the hardening process, undesirable structural changes in the metal may occur on a thin blade, and all the positive properties of the steel will be negated.

Some experts use diamond files for sharpening; you can often hear about craftsmen who bring the blade to the required sharpness on a sanding belt.

I strongly do not recommend using commercially available sanding belts for sharpening. The rotation speed of the belts is too high, which can lead to overheating of the metal due to friction and thereby reduce the degree of hardening. Sanding belts with adjustable rotation speed can only be used for rough sharpening, and then only at low speeds and provided that the master already has some experience. Using a sanding belt is not easy to achieve the same sharpening angle on both sides of the blade, and the blade can be ground down quite quickly.

For beginners who do not yet have sufficient experience in such types of work, it is recommended to use a sharpening set that allows you to adjust the sharpening angle,

which is the same on both sides of the blade and retains its shape, unlike the angles obtained by hand sharpening.

In addition, here you can choose a smaller or larger sharpening angle to suit your taste or depending on the application of the knife. For rougher work, a larger angle is better, but if the blade needs to be razor-sharp, then the sharpening angle should be small.

You can purchase such a device by clicking on the link and buy it at a discount.

Knife lovers can splurge on an expensive but high-quality Japanese whetstone, which can be used to sharpen blades by hand, but this work requires practice and a lot of time.

When sharpening a blade, quite strong burrs appear, especially on high-alloy steels. There are two ways to get rid of them: the blade can be processed on a grinding or polishing wheel using polishing agents. Or, according to the old grandfather’s method, use a leather belt attached to a wooden block.

How can you check that a knife is sharp?

There are several ways:

try shaving the hair on your arm or cutting off a few hairs on the back of your head, scratching your fingernail, cutting a rope, etc.

A test with a sheet of typewritten paper turned out to be very practical: take the sheet by the corner with two fingers and cut it diagonally with a knife. If this can be done in one smooth movement without jerking, then this indicates that the knife is sharp.

This post may contain affiliate links. This means I earn a small commission from links used at no additional cost to you. See my privacy policy for more information.

polishing, knife, weapon, article, photo, sharpening

Manual polishing

In the past, craftsmen from all over the world did not have special equipment, but somehow managed to get the job done efficiently. They polished knives without any special equipment. They used natural abrasive materials such as stone.

You can get the correct shape of the blade by grinding. It is possible to achieve a perfectly smooth surface using manual polishing. Using special mechanical devices, it is not always possible to obtain an ideal surface.

By all rules, hand polishing is the final treatment of a knife. To polish a knife at home yourself, you must first resort to grinding. It is produced on belts with a grain size of no more than 320. Or the surface should first be treated with sandpaper.

Blades polished to a shine.

Grinding

At the first production stage, after sawing, welding or casting, grinding of the still rough material is carried out. Its task is to remove irregularities and burrs from the surface, remove scale or old coating and bring the product to the required dimensions and shape. To perform this type of work, specialized mechanisms are used, which come in several varieties. They operate at the same high speed.

Grinding the bevel of the knife.

In some cases, you can use a primitive method, which consists of using granulated sand as an abrasive. The blade is rubbed against it until the protrusions on the plane are completely destroyed. You can polish something only with the help of rough mechanical action.

Features of sanding

Processing with sandpaper.
To polish a product with sandpaper, the first step is to sand at an angle of 90 degrees. But at the same time, irregularities may appear on the knife. This can happen if the paper becomes clogged with small particles.

In some cases, these bumps may go away. But you may have to switch to a larger grain again.

To carry out high-quality work, you will need good lighting, and the process must be performed under a magnifying glass.

When removing large irregularities, you can again switch to fine-grained paper. The polishing process can be carried out with different papers, the main thing is that the transition from one to another is smooth. This means that the grain of the paper should not change sharply.

You can start with paper with a grain size of 600, then increase it to 800. Next, polishing is done in an increasing manner. And so you should go up to 2000. And perhaps you should resort to 3000 sandpaper.

Bottom line

Basically, all polishing methods boil down to one thing: it is necessary to use a large amount of abrasives, gradually reducing their grain size. Various objects can act as abrasives: various stones, sandpaper, tapes with special compounds, etc.

As an encouraging parting word for those who will try their hand at this difficult task for the first time, here is an interesting fact: according to Japanese standards, only the one out of hundreds who has studied for at least five years with a master of his craft and has “God’s spark” for this can become a first-class polisher "

Abrasive stones

Stones, like paper, come in different grain sizes. The most popular are 320,400 and 600 units. For proper grinding, experts recommend using Indian bench stones. This method has been used for a long time.

Stones are good for removing unevenness from metal. In the old days, sand and soil were used for these purposes. And for polishing, stones with a structure harder than the blade were used. The most popular stone for polishing is sandstone.

How to use stones correctly

Stones of different grain sizes are used for grinding and polishing. You can examine the structure of the stone under a magnifying glass. Coarser stones are necessary when removing large scratches that remain after filing a blade.

To prevent the surface of the stone from clogging, it must be periodically moistened with water.

Arkansas stones are not bad for such work. They come in grain sizes up to 1000 units. The material is perfect for finishing.

At the very beginning of polishing, a coarser abrasive is required, and these stones are not used. Japanese wet stones are also very good at working. In addition to natural ones, there are also artificial ones. They are a little cheaper in cost.

Abrasive stones of different grains.

How to protect the blade from corrosion?

To avoid the problem of rusty deposits appearing on a knife blade, it is necessary to protect the steel from exposure to adverse factors .

First of all, they include moisture. Immediately after use, knives should be washed and dried with a towel.

Prevention requires compliance with storage rules . Sharp instruments are stored in oiled paper or special stands. This must be done for safety reasons, as well as to protect the blade from moisture.

If the knife is used for technical purposes, it can be wiped with kerosene. If it is not possible to use this substance, the blade is covered with a thin layer of wax.

To prevent the onset of corrosion and apply the cleaning agent in time, it is recommended to use the knife as often as possible.
Even decorative items hidden in sheaths require periodic inspection .
If water gets into the folding knife hinge, it is advisable to remove it with a hair dryer. Otherwise, the inaccessible damp area will be where corrosion begins.

Knife grinding

Process the blade into a rectangular piece, the easiest way is to use grinding machines. It will take less time, but requires a process of precise eye and sense of proportion.

It is impossible to see the degree of grinding between the knife and the tape.

In this case, the master relies on his feelings. He literally has to feel the process taking place. The master must mentally imagine and feel each pass of the tape or circle. If you do the operation repeatedly, muscle memory will appear.

When sanding, you should follow a few tips, they are mandatory for a beginner:

1. It’s better to start with simple shapes and a short blade length. Use a template to apply the outline to the workpiece.
2. Carbon steel grades are easier to process. Make the workpiece strictly rectangular in shape.
3. The basis for such work is considered to be muscle memory. Take several blanks at once and perform the procedure with them one by one. Making a blade from start to finish is not advisable.
4. Equip your workplace with good lighting. Wear comfortable shoes to help you balance properly during the process.

Final grinding and finishing are carried out with longitudinal movements along the machine belt. At the initial stage, it is best to use a tape grain size of 60-80 units. Further work is carried out with a slightly smaller grain of 160-240.

The entire blade is processed with any grain. After completing the grinding process, the product is hardened. After this, the workpiece acquires the necessary rigidity. Next, processing is carried out with finer abrasives. But this will already be a polishing process.

Blades after polishing.

How to clean with chemicals

When the corrosion layer is already quite dense, it is not always possible to correct the situation using “folk” methods. There are several “lifesavers” that allow you to deal with the problem quickly enough, and the result can be seen literally after a couple of minutes.

Alka-Seltzer

The drug for headaches can be found in almost any pharmacy. But in addition to physiological ailments, it also copes with rusty deposits with a bang.

To clean, you will need five tablets and some running water in which to dilute them. At the same time as the preparation, dip a rusty knife into the liquid and remove it immediately after the bubbles disappear. Then remove any remaining dirt with a soft cloth and polish.

Zinc chloride + potassium hydrogen tartrate

Combine 0.5 g of potassium hydrogen tartrate with five grams of zinc chloride in 100 milliliters of water. Further actions are similar to using the previous drug. It will take 2-3 hours to dissolve the rust.

Hydrochloric acid

Hydrochloric acid, or, alternatively, sulfuric acid, is recommended to be used in combination with special inhibitors that reduce the destructive effect of these substances on the metal.

The object should be immersed in a 5% acid solution with the addition of methenamine (1/2 gram should be diluted in one liter). A large knife is processed using a brush.

Important: when using strong chemicals, be sure to use tongs or tweezers to immerse the product in them, as well as thick rubber gloves and protection for the face, especially the eyes.

Special reagents from the store

Use store-bought preparations to combat oxide stains with caution - be sure to protect the skin of your hands with gloves and open the windows slightly so as not to inhale the chemical amber.

Before applying the product, it is necessary to prepare the surface - if the rust is a protrusion, it must be leveled with sandpaper to the level of the blade, and the loose layer of corrosion must also be removed.

There are several types of purchased drugs:

• Rust converters.
• Rust removers.

And if everything is clear with the latter, then an explanation is required regarding the first point so that you can decide on the choice of composition - converters convert metal oxide hydrates into denser compounds, which also prevents rust from spreading over the entire surface.

Among the most popular are Adrilan, Omega-1, Avs Avk and Runway.

Polishing the knife

The steel acquires a uniform matte finish after the grinding process. The surface must be absolutely smooth, with no dents or potholes allowed. Otherwise, the result of polishing the workpiece will disappoint you. Polishing is carried out on a belt machine.

But such a tool costs a lot of money, and not everyone has it. You can resort to using an angle grinder; this method is most accessible to ordinary citizens. Let's look at the process step by step:

1. It is necessary to prepare the blade for work. The handle can be wrapped with masking tape, or even better if it is possible to temporarily dismantle it.
2. You will need not a simple grinder, but one with the ability to switch speeds. The speed should be as low as possible. The grain size of the wheel at the first stage is required to be 320 units, or you can use a special polishing mixture based on SF glue.
3. Next comes changing the disc to a felt one. Here you will need polishing paste. The grain value of the mixture should be in the region of 600-800 units, the manufacturer does not play a role. You need to be careful when processing; just go over the blade a couple of times on each side.
4. After the previous step, the abrasive paste is removed from the wheel and ointment with a grain size of 1200-1600 units comes in its place. Next, you should carefully, without strong pressure, walk along the blade several times. The procedure should be performed to a mirror shine.

The polishing process takes a lot of time. Be sure to complete all processes in strict order. You should act confidently and not be nervous when you fail. Choose the right abrasive paste with the right grit. Any little thing can affect the result.

Blade before and after polishing.

Polishing

Polishing the knife is the final stage. Its function is the final leveling and transformation of a matte surface into a glossy one. It is unrealistic to achieve a similar result using rough processing. The design of polishing machines is somewhat different from grinding machines. They operate at lower speeds, which can also be adjusted. Also, there is no way to do without polishing pastes.

Excellent polishing quality can be guaranteed not only by mechanical impact, but also by chemical impact, which exposes the metal to the influence of the active composition.

Quick polishing by hand

Many professionals say that the polishing process is best done by hand. Movements are made carefully along the blade. With this tactic you can quickly polish the blade. But there are specialists who use a grinding machine.

The rapid rotation of the circles polishes the blade faster. But this does not mean that the quality is better. This method has its drawbacks. The surface of the blade is not always perfectly smooth. It may show rough waves or scratches.

If the scratches are in one direction, this can be quickly corrected. After rough processing, it is necessary to prepare a small piece of leather and a special polishing compound with a grain size of 1600-2000 units. This paste should be used for finishing, but by hand.

Have you tried polishing the knife?

Of course! Not yet...

Additional Tips

You can use any suitable method to remove rust marks from a knife. When choosing a product, you should focus on the degree of contamination, financial costs and the possibility of using the method.

In any case, it is advisable to take into account additional recommendations that will facilitate the cleaning process and help speed it up:

1. 
   If the rusty coating is significant and has not disappeared completely after the first treatment, it is necessary to repeat the cleansing with the same product or choose a different one.

2. If the corrosion process has gone far and a solid, dense coating of rust has formed on the knife, then it is advisable to first remove it mechanically (with sandpaper), and then complete the cleaning with any liquid agent.
3. When using any chemical reagents, it is necessary to wear rubber gloves to protect your skin.
4. After complete removal of rusty traces, the blade is thoroughly washed with water and dried well. The presence of moisture can reinitiate corrosion.

Application of dry and wet paper

Polishing work can be carried out with dry or wet paper. The material is lubricated with water so that it does not deteriorate or become greasy during the process. But for a certain type of work, only dry paper is required.

In order to polish a knife at home using paper, you will need to purchase a special kit.

It can consist of many sheets of different grain sizes. This will be the most economical. Waterproof material is more durable, this should be taken into account.

To polish a metal surface, it is best to use paper treated with silicon carbide chips. For a correct and convenient process, follow these tips:

• paper should be folded in half;
• the workpiece should be fixed using clamps to any surface;
• paper folded in half will not slip out of your hands when working.

Something about safety measures

I find it dangerous to place a polisher directly on a table or workbench. When the polishing wheel grips the blade, it flies at 75 miles per hour or more towards the surface of the workbench. Such a pointed rocket can bounce off the workbench and, hitting the wheel again, go directly to the master.

Mount the machine on a workbench extension no larger than the motor base. The idea is to ensure that there are no obstacles between the circle and the floor. Some kind of soft mat should be placed under the polishing wheel so that the blade, falling down from the wheel, does not get damaged or, even worse, fly off the wheel towards the operator.

A few years ago I was teaching a friend how to make knives. In a hurry, he set up his polishing machine directly on the workbench. The polishing wheel grabbed the dagger's guard and threw it straight onto the surface of the workbench. Bouncing off the workbench, the dagger again hit the circle, which sent it straight into my friend's hand. The friend did not receive any injuries, but he did not go to work for a long time and spent a lot of money on treating his hand. I know more terrible stories about accidents caused by the polishing wheel, but I won’t tell them here. I will just repeat that, from my point of view, a polishing machine is the most dangerous tool in a cutler's workshop.

Protection should be installed over the circles. The photo shows how I did it.

Even if you've never had anything bounce off the wheel in your face, it's good to have dust and bits of polish flying onto the floor and not at you.

My circle guards are made from 3/4″ plywood, glued and screwed together. I hope that the blade of the knife, wrapped around the wheel, will get stuck in the tree, and not in me. When the wheel works, the protrusion on the front of the protection can be moved lower. The upper part of the machine protection is convenient for storing polishing compounds and other small items.

Mirror processing

Any knife will look attractive with a blade polished to a shine. To polish a knife blade to this condition, you will need special secrets. Each master has his own polishing methods.

Whichever option is used, the result should speak for itself.

To achieve an ideal surface, the product can first be sanded by machine.

And only at the finishing stage should you start polishing by hand.

Preparation at the grinding stage also plays a significant role in the final result. Handle grinding wheels with care. High machine speed can damage the product. The grinding wheel must be used with a soft surface.

How to clean with special compounds?

Knife owners who do not trust folk recipes or, for subjective reasons, prefer to use household chemicals, can choose a product from the store. The range of ready-made rust converters is quite wide. The most popular are time-tested liquids and concentrates.

Adrilan

The Russian product, positioned as a fruit gel , is intended to remove rust marks from the surface:

• metal utensils,
• tool,
• plumbers.

The gel does not contain abrasive particles and does not damage the surface. In addition to the anti-corrosion effect, Adrilan has a disinfecting effect.

The gel is evenly applied to the surface of the blade and left for a short time. Then the brown mass is removed from the blade with a brush and washed with water. A bottle weighing 0.664 kg sells for an average of 80 rubles.

AVS AVK

A liquid product containing active zinc ions, inorganic acids and functional additives in the formula . Zinkach is suitable for cleaning steel and cast iron products from a layer of rust up to 80 microns thick. The zinc converter further protects the metal from repeated corrosion.

Shake the contents of the bottle before use. If necessary, remove the loose layer of rust. Next, apply the product evenly to the blade. Leave for 30 minutes and apply a second layer. The cost of a small 60 ml bottle is on average 50 rubles.

RUNWAY

Professional rust remover and converter made in America. Can be used for any metal surfaces, except galvanic ones . RUNWAY is used for domestic and industrial purposes.

The product is applied to the metal surface for several minutes. Remove any deposits that have formed and dry the surface. A small bottle (30 ml) sells for 90-110 rubles. A larger bottle (120 ml) is estimated at 220-250 rubles.

Using GOI paste

The method of working at the finishing stage with GOI paste has been known to masters for a very long time. To polish a knife with GOI paste, you need to select the appropriate type of polishing material. It will depend on the grade of steel of the workpiece being processed.

Using GOI paste, metal, plastic and glass surfaces are polished. Previously, it was made from chromium oxide and was green in color. Today it is made of aluminum oxide, and its color has become red and white.

What can't be used and why?

Do not use too aggressive preparations to clean the blade and mechanism of the knife . If you have doubts about the product, before use it is recommended to apply one drop to the edge of the product to track the reaction and see the result.

GOI paste should be used with great care for polishing. It gets stuck in the smallest cracks and cavities, from where it is difficult to remove.

This is especially true for antique knives that have carved steel handles. It is better to entrust the cleaning of such items to specialists.

Types of pasta

In the old days, there was only one type of paste available. Now masters have a choice. It is produced with various grains:

• number 4 is used for rough work, it is used at the initial stage of polishing;
• to obtain a matte surface use number 3;
• and for final polishing numbers 1 and 2 are used.

Green pasta, like in the past, can still sometimes be found on store shelves. Previously, such paste was produced in liquid form and in bars. They were absolutely identical in grain size. It has only one advantage - low cost.

Various GOI pastes.

How to use GOI paste

You should prepare a small piece of cloth. The process does not look complicated; you should rub the surface of the blade with progressive movements. It doesn't require much pressure. Otherwise you may get big scratches.

Movements should not be too sudden. The work should be completed when the blade begins to shine.

For proper treatment, you should first use paste number 4, it will remove all deep scratches. Then move on to number 3.

And at the finishing stage the surface is treated with numbers 1 or 2. These types of paste allow you to achieve a mirror shine. After work, you should rinse the blade in running water. But you can also rinse in kerosene. It is also recommended to cover the surface with tsaponvarnish.

How to restore the original appearance of a product using folk remedies?

Iron oxides and hydroxides that appear on the surface of a steel blade can be easily removed using homemade “reagents.” Such products are valued for their ease of use and affordable price .

Vinegar and lemon juice

These products contain organic acids (acetic and citric), which actively interact with iron oxides. The resulting salts are easily washed off the metal surface, restoring its cleanliness and shine. Chemical cleaning is considered one of the most effective ways to combat rust.

The instructions for using the lemon-vinegar mixture are simple:

1. 
   Vinegar (6-9%) is mixed with lemon juice in a volume ratio of 1:1.

2. Generously moisten a cloth in the resulting solution.
3. Wrap the knife blade in a cloth soaked in liquid.
4. Leave the product for one hour for the reaction to occur.
5. Wipe the blade with a sponge, rinse and wipe dry.

When cleaning at home, it is not recommended to use vinegar essence. The entire procedure using vinegar must be carried out with the window open or under a hood.

Read this article about using vinegar against rust.

How to get rid of it with tomato paste?

A natural tomato product has a mild anti-corrosion effect. The effect is also based on the content of acidic substances in the product.

If you don't have tomato paste, you can replace it:

• fresh tomatoes,
• tomato juice,
• ketchup.

To remove oxides, tomato paste is applied to the blade in a continuous layer. Leave for 40-50 minutes, then wipe with a sponge or cloth. If the spots have not disappeared 100%, repeat the procedure.

This home remedy compares favorably with analogues in its safety and ease of use. However, it only helps get rid of small rust stains that have recently appeared. To remove thick deposits, it is recommended to use a stronger cleaner.

Coca Cola

The carbonated drink is a popular means of cleaning rust from metal surfaces.

Phosphoric acid contained in drinking liquid is an active rust converter.

The method using Coca-Cola (Pepsi, Fanta or other similar drinks) is in demand due to its high efficiency and availability.

Coca-Cola is poured into a low container, the product is placed in it and left for 30-40 minutes . After the specified time, check the result by lightly rubbing the blade with a sponge. If orange traces remain on it, the exposure time is extended by another 15-20 minutes.

Read about the use of Coca-Cola against rust in this article.

How to remove plaque with Vaseline and lactic acid?

The combined product helps clean the blade from rust and at the same time protect it from re-corrosion. Lactic acid acts as a purifier, which neutralizes the oxide by forming it into iron lactate, soluble in liquid paraffin.

The product is prepared by mixing one portion of Vaseline paste with two portions of lactic acid. This mass is distributed over the blade and held for half an hour. Then apply petroleum jelly to a cloth napkin and wipe the knife with it, removing any remaining rust.

The method is considered effective, but its use is somewhat limited due to the fact that pure lactic acid is not available in every home. To prepare an anti-corrosion agent, instead of Vaseline paste, you can use wax or paraffin .

Vegetables

This category of cleansers includes potatoes and onions. The juice that tubers and bulbs secrete contains organic substances of an acidic nature. They are the ones who determine the high efficiency of this method. To make cleaning easier, use salt, baking soda or laundry soap as additional ingredients.

The cleaning procedure is as follows:

1. Cut the potato or onion in half.
2. Sprinkle the cut with salt, soda or planed soap.
3. When juice appears on the cut, wipe the knife with a vegetable slice.
4. Leave the product on the blade for 30-40 minutes.
5. Wipe the knife with a sponge, removing any remaining marks.

If necessary, during cleaning, the blade is re-moistened with potato or onion juice to prevent the surface from drying out.