Hot-rolled sheet. (Hot-rolled sheet and coil steel) GOST 19903-74, GOST 19903-90

Steel sheet 2, 3, 4 mm - dimensions, weight 1 m2, price per sheet, ton

Steel sheets with a thickness of 2 to 4 mm are produced in sheets or rolls. It is considered thin-sheet steel with certain physical and chemical characteristics, which APEX metal buyers successfully use in accordance with its intended purpose:

• Cold-rolled products made from high-quality carbon and low-alloy structural steels have less variation in thickness and surface roughness, have good technological qualities, uncoated and galvanized sheets are suitable for the manufacture of products obtained by cold stamping, drawing, and profiling methods
• Thin-sheet hot-rolled steel is used for shallow stamping and production of flat products, hot forming, further processing into cold-rolled metal, cold machining

Below is a price calculation for sheets of 2, 3, 4 mm, as well as the calculated characteristics of thin-sheet and thick-sheet rolled products, which can be purchased from the warehouse at APEX metal.

Steel sheet 2 mm - dimensions, weight 1 m2, price per sheet, ton

Steel sheet 3 mm

Steel sheet 3 mm - dimensions, weight 1 m2, price per sheet, ton

Steel sheet 4 mm

Steel sheet 4 mm - weight 1 m2, price per sheet, ton

Sheet processing on automated cutting lines

At ARECH METAL you will buy standard factory-cut sheets, and you can also order sheet cutting for further processing. For this purpose, automated cutting, cutting, stamping, and profiling lines are used.

This service allows clients to use material economically, with a minimum of trimming waste, and to cut blanks of non-standard sizes. To clarify the cost of cutting thin-sheet and thick-sheet rolled products, please contact the Sales Department by phone. +.

Sheet 3 mm

Steel sheet 3 mm thick (GOST 19903-74, GOST 16523-97)

This is a multifunctional material from which household and construction metal structures are made.
3 mm is the ideal thickness for the production of armored doors, entrance gates, boxes, containers and other metal products. It can be deformed and welds perfectly using any welding method.

The structure will be much stronger if stiffeners are used. In addition to the classic type of welding, the 3 mm thickness is also cut to size. Oversized 3mm steel, easy to transport even with light transport. Order a 3 mm thick steel sheet from us and receive special terms of cooperation and prices.

Hot rolled steel sheet (GOST 19903-74)

It is produced using the hot rolling method from low-alloy, structural or stainless steel of various grades. This rolled metal has various thicknesses and a smooth surface (thickness from 0.5 to 160 mm).

This type of rental has a number of advantages:

• Resistance to mechanical stress
• Plasticity, the metal lends itself well to various processing methods.
• Versatility, sheet metal is in demand in various branches of mechanical engineering and other industries.
• Low cost due to relatively low production costs

It is used in mechanical engineering, automotive industry, machine tool industry; various bodies, components of mechanisms and much more are made from it.

We offer the following standard sizes with a thickness of 3 mm:

“Hot-rolled steel sheet 1250x2500” - technical characteristics:

• GOST - 14637-89, 16523-97;
• Weight - 75 kg;
• Steel grade - St. 3;
• Rolling method: hot rolled;
• Coverage: uncoated;
• width – 1250;
• length - 2500;
• Thickness - 3.

Product of rectangular cross-section with cut or uncut edge

“Hot-rolled steel sheet 1500×3000” and “Hot-rolled steel sheet 1500×6000x3”

Specifications

• Thickness - 3
• Width - 1500
• Length - 6000
• Technical specifications - GOST 19903-2015
• Steel grade - st3sp5
• Weight of 1 square meter - 23.5 kg
• Weight of one sheet - 211.9 kg

It has a convenient cut for subsequent cutting or processing. Can be used to produce various types of boxes, electrical cabinets and panels. Fence posts as elements of built-in reinforcement products.

Place an order at a competitive price: call the numbers provided or leave a request on the website.

Expanded metal sheet (PVL)

This is a steel sheet with a special structure. During the manufacturing process, a massive steel plate is simultaneously cut and stretched on special machines. This gives the finished product the appearance of a solid metal lattice.

Depending on the production, PVL is distinguished between cold-rolled and hot-rolled; it can also have a galvanized or non-galvanized surface.

Advantages:

• Light weight
• Flexibility. Sheet metal is easy to bend
• Easy to install
• Inexpensive. There is virtually no production waste in the production process.
• Large selection of products with different cell sizes.

Expanded metal sheets of various thicknesses, namely 3 mm, are presented in the catalog. Check out the catalog, choose the appropriate type for wholesale or retail orders at a competitive price. We offer to buy expanded metal sheets with delivery throughout Moscow and the Moscow region.

Expanded metal sheet 1000x2500x3 (GOST 8706-78)

• Brand - PVL 308
• Thickness - 3
• Steel grade: 3SP/PS
• Cutting - 1000x2500
• Coverage: uncoated.
• Standard - TU 36.26.11-5-89.
• Type of perforation - rhombus, scales, honeycomb.

Used for flooring, stairs, fences, verandas. Installation of reinforcing mesh during plastering work in construction.

Corrugated steel sheet (GOST 8 568-77)

This is a metal sheet made of carbon steel with a convex geometric pattern printed on one side. Thanks to it, the sheet acquires anti-slip properties, which provide a variety of uses for the finished product. Variants of the pattern “Rhombus”, “Lentil”, “Duet”, “Quartet” have become widespread. Steels St0, St1, St2 and St3 are used for production; the type and purpose are determined by the corrugation pattern.

This type of product has several important characteristics:

• Anti-slip properties.
• Durability, high resistance to mechanical stress.
• Flexibility and ductility, which allows the sheets to be used for finishing a wide variety of surfaces.
• Relatively light weight.
• Aesthetic appearance. This type of product has good decorative qualities.

The catalog presents a wide range of high-quality sheet products, in particular “Corrugated hot-rolled 1250x2500x3”.

Specifications:

• Width - 1250;
• Length - 2500;
• Thickness - 3;
• Rolled products - Hot rolled (hot-rolled);
• Carbon content - C 0.17-0.24;
• Type - lentil.

The riffles on it have an oval shape, reminiscent of the grains of the plant of the same name, while their longitudinal axes are located at right angles to each other.

We provide high quality sheets manufactured in strict accordance with current standards.

Products made from sheet steel are in demand in many industries: mechanical engineering, construction, carriage building, etc.

Our company offers the purchase of steel sheets in an assortment. On sale there are hot-rolled, cold-rolled, galvanized, corrugated, expanded metal sheets with a thickness of 2 to 8 mm, wholesale and retail supplies are possible.

Sheet metal: standard size, thickness, width and length of various types of rolled material

Sheet metal is produced in the form of wide strips and sheets by rolling or forging (less commonly). Sequential processing is carried out by cutting (laser, mechanical or plasma), flexible, punching. In some cases, a combination of several metalworking methods is used. Mechanical cutting is done using a guillotine and scissors, bending and punching is done using a press.

Characteristics of sheet material

Hot-rolled steel sheets are heated and subjected to deformation in rolling mills and presses. To avoid defects in the form of different thicknesses, the material is processed by cold rolling, which increases its useful characteristics.

Depending on the production method, a distinction is made between hot-rolled (HK) sheets and cold-rolled (CC) sheets. Proportional metal plates in thickness range from 0.36 to 3.98 mm (dimensions of thin-sheet steel) and from 4 to 160 mm (dimensions of thick-sheet material). There are rolled products with cut and uncut side edges.

Plate sizes

The material is widely used in industry, so it is necessary to produce many standard sizes of products. The average value of a sheet with a width of 1.25 m and a length of 2.5 m is taken as the standard.

Hot-rolled and cold-drawn products have different dimensional parameters. The thickness of the metal sheet varies depending on the purpose of application and production technology. Depending on the thickness, the weight of the product changes.

Main dimensional parameters:

1. With a sheet thickness of 3 mm, a width of 1.5 m and a length of 6.0 m, the plate weighs about 72 kg. The maximum thickness of cold-drawn steel is 0.4 mm.
2. The standard common size of a cold sheet is 1.0 x 2.0 meters, while the size of the strips is 1.2 x 2.5 m; galvanization has slightly different dimensions, despite the standardization of all materials according to GOST 19904–1974.
3. Galvanized standard strips are 0.55 mm thick; products are available in thicknesses of 1.4 mm, 1.2 mm, 1.0 mm, 0.7 mm, 0.5 mm, 0.45 mm, and 0.4 mm. The width of galvanization is usually 1.25 m with a length of 2.5 m.
4. Hot-rolled steel plates are produced in sizes of 1.25 x 2.5 m, while the thickness ranges from 0.5-3 mm, and the sheet thickness is added at intervals of 0.5 mm. Thick-walled plates have large dimensions, they are produced in 1.5 x 6.0 m and 2.0 x 6.0 m, 2 mm sheet metal is widely used. Sheet weight ranges from 13.5 kg to 64 kg with a minimum and maximum strip thickness.

Difference between cold-drawn and hot-rolled methods

Manufacturing involves passing the workpiece through specially prepared rollers. This reduces the thickness and adjusts it to the required length and width.

As a result of using different production technologies, wafers are obtained whose properties differ from each other. The choice of method for producing steel strips depends on the intended purpose for further use.

Deformation at high temperatures is carried out under conditions exceeding the recrystallization rates of the material. The temperature should rise to 60% of the metal melting indicators.

The initial workpiece is called a slab. The ease of deformation at high temperatures is explained by the fact that the strength of steel decreases.

This circumstance makes it possible to reduce the force aimed at giving the workpiece the desired shape.

Cold rolled products are characterized by deformation at temperatures ranging from +20...+25˚С (room temperature). The initial workpiece is represented by a hot-rolled plate. Before forming, the material is cleaned of scale using sandblasting, shot blasting units, or using acids and their compositions.

Deformation at low temperatures, below 30% of the melting point, causes the formation of strain hardening (hardening) in the sheet body.

This increases the strength of the plates and reduces ductility; for deformation, the force load must be increased.

To partially recrystallize the structure, reduce hardness and make the material plastic, tempering is done in the form of additional heat treatment.

Hot deformation

Steel contains different elements, so when heated it is impossible to ensure a uniform increase in temperature. Rolling of a well-heated section proceeds faster than a cold one; the process is carried out with different parameters, which leads to the appearance of defects. The difference between cold and hot produced sheets can be seen with the naked eye.

The method makes it possible to obtain products in a sufficient range of thickness to satisfy consumer needs. Such sheets are used for coatings in construction. At the same time, a lot of money is not spent on the production of plates. The material has increased corrosion resistance compared to cold produced sheets.

The disadvantages of production include the following points;

• there are surface imperfections, there are areas of scale that need to be removed;
• it is impossible to obtain very thin plates;
• dimensions have low accuracy;
• welding negatively affects the quality of the product.

Cold rolled products

The method makes it possible to obtain very thin flat sheets of several microns, and the geometric parameters of the product are highly accurate.

The result is a high-quality and smooth surface; such material can be used for the production of objects and parts in cases where the aesthetic side of the product is important.

In construction, cold-drawn metals are used for cladding walls, floors and other finishes. The popular use for welding is due to the fact that the material does not conduct with this method of joining.

The disadvantages of cold-rolled products include the following characteristics:

• poor resistance to corrosion in the open air without an anti-corrosion protective layer;
• sheets have reduced ductility due to increased hardness;
• the high cost of production affects the price of the material, this is explained by the use of many complex units and the use of large amounts of energy.

Areas of use

The different uses of materials in industry are due to the variety of properties. Products obtained by hot and cold methods have different properties. Hot rolled metal plates are most often used:

• in the construction of ships, airliners, cars, the material is used in structures where the joints are connected using hardware and without welding;
• in the construction field, metal is used in the form of load-bearing frame elements and in the manufacture of internal structure elements with subsequent finishing;
• for the manufacture of pipes by soldering;

Cold drawn sheet is used in the following cases:

• in the production of corrugated sheets and for the production of smooth galvanized sheets;
• in automobile production;
• for the production of thin sheet metal with a tin covering layer, used in the production of canning containers;
• in the manufacture of decapir (annealed plates) used in the production of enamelware;
• a high-quality smooth surface requires its painting with powder compositions, nickel plating and chrome plating;
• for cold stamping.

Visible sheet defects

During the manufacturing process, surface defects or dimensional deviations occur. They are classified into certain categories. The appearance of deviations and defects of a certain type is characterized by improper organization and equipment of the production process.

Scratches, irregularities, oblique cuts

Such violations are characterized by the appearance of mechanical damage to the strip in the form of depressions across and along the rolling direction. Deviations in dimensions in length and width from the standard specified parameters are diagnosed by an amount exceeding the permissible values. On the surface, protrusions of material are formed along the width and length at the edges of strips or sheets, having a right angle with the surface.

The reasons causing such deviations from the norm may be:

• metal elements of equipment protruding beyond normal limits, sometimes defects are caused by stuck pieces of metal;
• poor adjustment of flying or disc shears, or their weak fastening during installation;
• untimely sharpening of knives;
• crescent shape of the strip itself;
• improper organization of feeding of rolled strip into the cross-cutting machine;
• unprofessional setting of pulling and feeding rollers.

Fat, wave, scatter and crescent

A slight waviness of the rolling strip appears along both edges or only on one side. On the surface of the plate, prints of various sizes and shapes are visible in the form of elongated spots or stripes. Smoothness is disrupted by the appearance of sharp holes, grooves and imprints of mechanical origin.

There are kinks and bends on the plate in different directions, corners and edges are often bent. When packing sheets into bundles, a shift in the size of the sheets along the width or length of the package relative to each other appears greater than the permissible norm. Damage of one kind or another is noted on the side edges, the corners may be curled, and the strip itself has a crescent shape.

Defects are caused by the following reasons:

• misalignment of feed and receiving rollers or rollers;
• poor adjustment of the correct rollers and disc knives;
• waste and other metal parts stick to the rollers and straightening rollers;
• the strip is not protected when cutting from small metal shavings and parts;
• jamming of rolled material in packaging devices;
• improper threading of the strip for advancement with pulling and straightening rollers, sagging and pressure on the roll screws from the outside;
• careless adjustment of wiring fittings, malfunction of the conveyor belt, incorrect height adjustment of the pocket and lifting table;
• installation of stops in baling units (in their pockets) in violation of standards;
• Incorrect adjustment of scissors and loosening of vertical rollers and wires.

Protective films against corrosion

This concept refers to coating the surface of a metal with a zinc-based layer to improve protection against damage and corrosion. The principle of protection is based on certain properties of non-ferrous metals. Aluminum, zinc, and tin oxidize in the open air, resulting in the formation of a film. It does not allow oxygen into the metal and inhibits further oxidation.

In hardware the process occurs differently. As a result of oxidation, compounds appear, hydroxides, characterized by an increase in volume relative to the original metal. Because of this, the film becomes loose and quickly collapses. It does not protect the body of the intact metal from oxygen, and oxidation affects the internal layers.

Iron does not tolerate air well, so a rusty layer forms on the surface. To protect against this, a protective film made of non-ferrous metals, such as tin, is used, which protects the iron from destructive corrosion.

The principle of operation of tin and zinc is approximately the same as long as the protective film is not damaged until the iron is exposed. If the iron is coated with zinc, then together they create a galvanic couple. When reacting, iron is more passive compared to zinc, which oxidizes first, and the iron is protected because of this.

Tin also forms a pair with iron, but is not an active substance, therefore, if the tin layer is damaged, iron is the first to oxidize, which provokes its further destruction and corrosion at the site where the integrity is damaged.

Features of dynamic steel

Strips of dynamic cold-drawn steel differ from strips obtained by the hot method because they are thicker, have a better surface, and are free of scale. The high characteristics of dynamite steel are used in the manufacture of electrical machines. This gives a high fill factor, saves energy, and increases power with older dimensions.

Supplying cold rolled steel in strips offers advantages in cutting and receiving due to less waste. Due to high-quality processing, dynamic steel has more stable properties.

Standard sheet metal dimensions are 2 mm. Steel sheet

The combination of strength characteristics, ductility and relatively low specific gravity make it possible to use thin sheet steel quite widely. Air ducts and ventilation shafts are made from it, and they are used as lining for the internal and external surfaces of various structures.

Flexibility makes the metal sheet 2 mm

universal material. The cross-sectional configuration of the sheathed surfaces is different - the sheet fits equally well on square, oval and round structures. Welding and locks are used to secure the shape.

In addition, a thin sheet can become the main material in the production of galvanized steel, since it is able to maintain relief and can be easily deformed.

2 mm steel sheet: manufacturing technique

Sheet 2 mm thick

very popular among consumers. Both methods are popular, both the hot method, in which the billet is rolled in a mill at a temperature above the recrystallization range, and the cold method, during which the starting material is subjected to high pressure.

When choosing a manufacturing technique, you should take into account that the use of hot rolling technology does not always produce a 2 mm steel sheet

with a sufficiently high-quality surface that can satisfy the high demands of consumers.

Therefore, quite often when purchasing thin steel sheets, preference is given to cold manufacturing techniques.

The production of thin sheet metal is allowed from carbon steel of ordinary quality (OK), according to the acceptable steel strength groups - K490V, K390V, K350V, K330V, K310V, K270V and K260V. The numbers here indicate the limit of temporary resistance (its lower limit).

The regulatory and technical documentation also provides for the production of thin-sheet rolled products in two versions - in rolls and in sheets. The width is also indicated - from 500 mm, there is no upper limit. The entire size range is indicated in, at the request of the customer, deviations from the existing geometric parameters are possible. Therefore, sheet 2 GOST

does not violate.

Depending on the existing requirements for the accuracy of characteristics such as thickness, length and width, 2 mm metal sheet

belongs to one of three groups. And, accordingly, can be classified as high, elevated or normal. For sheet and coil products these indicators are different.

Cost of steel sheet 2 mm

Sheet 2 price is widely used

which depends on the cutting parameters. The cost of cold-rolled steel sheet is higher than that of a similar hot-rolled sheet, which is explained by a more complex technological process and higher energy consumption.

At the same time, the flawless surface does not require additional processing at the stage of applying paint and varnish coatings; in addition, high flatness characteristics reduce the time required for the manufacture of products, that is, the financial costs will ultimately be justified.

Also on our website you can calculate the weight of a 2 mm sheet,

by going to the appropriate section
« ».

Our company’s consultants, having many years of experience working with clients, are ready to give each client professional recommendations regarding the type of 2 mm sheet, taking into account the characteristics of your production. From us you can order sheets of 2 mm weight

which we will help you calculate.

Sheet 2 mm

hot rolled

Metal sheet 2 mm

- one of the most popular rental products in use. It is convenient to use for the production of thin-walled profile or electric-welded pipes, channels, angles, and PVL sheets.

It is used in construction, shipbuilding and mechanical engineering, the oil and gas industry, in heat and power engineering, for structural elements, various mechanisms, in the production of various household and agricultural equipment, instruments, decorative panels, in interior design, building cladding, and on personal plots. Corrugated sheet metal is made from thin sheet steel in rolls - for roofs, fences, walls and partitions. After rolling, the corrugated sheet is galvanized and painted for anti-corrosion properties. Sheet 09G2S is used at extremely low temperatures or at elevated temperatures, for parts exposed to pressure.

Leaf gk

St3 2mm is valued for its low cost, smoothness, ductility, malleability and flexibility of the metal, the ability to manufacture other types of rolled metal and various products from it, light weight and strength.

Hot rolled sheets can be welded. Its light weight allows it to be used to make hoods, air ducts, and any lightweight structures.

The disadvantage is the need for periodic painting and low fire resistance.

Sheet metal

2 mm hot rolled steel is produced as follows:
2 mm
hot rolled steel sheets are produced on continuous lines, which, when heated at temperatures up to 760 degrees Celsius and high pressure, pass through numerous rotating shafts, become wider and thinner, and then cold rolled to give certain properties, smoothness and improvement of metal quality.

A heated sheet has scale and unevenness, but rolling initially cold metal requires more powerful machines. In addition, the cold-rolled sheet must be additionally fired and heat treated to relieve the internal stress of the steel.

Therefore, hot-rolled sheet 2 mm is cheaper than its cold-rolled counterpart, and if there are no special requirements for the quality of the sheet, then hot-rolled sheet is used.

Sheet St3 2 mm

supplied by JSC Novolipetsk Iron and Steel Works, JSC Severstal, JSC Zaporozhye Iron and Steel Works Zaporizhstal, JSC Magnitogorsk Iron and Steel Works, JSC Chelyabinsk Iron and Steel Works and others.

Steel sheet 2 mm is classified as thin sheet and is produced in accordance with GOST 19903 in terms of assortment. Such a hot-rolled metal sheet 2 mm

produced according to GOST 16523 and GOST 17066.

Standard 16523 applies to all rolled carbon steel light sheets for general purposes. The steel used is high-quality or ordinary quality. These can be brands 08ps, 10ps, St1 - 3ps.

GOST 17066 requires high-strength steel; our company sells 2 mm sheets of steel grade 09G2S.

Rolling accuracy of iron sheet is 2 mm

There is increased and normal accuracy.
The edge of such a sheet can be trimmed or unedged. According to the flatness, the sheet is distinguished between especially high, high, improved and normal flatness. Sheet 2 mm hot-smoked
can be deep and have normal stretchability. Its surface finish can be either high or normal.

Sheet size 2 mm thick

JSC Metallotorg supplies hot-rolled sheet 2 mm

We will cut 1250mm * 2500 mm and 1000 mm * 2100-2300 mm.
With a sheet width of 1250 mm, the weight of a 2 mm sheet
will be 19.63 kg per 1 meter.

Buy hot rolled sheet

Buy sheet 2 mm

St3 or 09G2S is available from our company from any warehouse in Russia. We can move the missing tonnage to the branch closest to you. Our specialists will help you quickly and efficiently calculate the required amount of material, issue an invoice and deliver the metal as quickly as possible.

A 2 mm thick sheet easily fits into both an open gazelle and a valdai; it is not necessary to order a long one, which will significantly affect your budget. We also provide the service of cutting sheets of 2 mm in size. This thin sheet is packed in the warehouse with tape for safe transportation.

Iron sheet 2 mm price per sheet

Our managers will advise you, and the price per ton is indicated in the price lists of our organization.

Retail steel sheets (cold-rolled, hot-rolled, galvanized, corrugated) produced by NLMK, Severstal.

Cold-rolled sheets are available for sale at retail (m2, pcs.) and wholesale (pack, ton)

Classification and use of rolled sheets

Industry and the construction industry widely use sheet metal to create a variety of structures. Steel sheet

Ideally suited for corners, channels, strips, and other elements.

Where is sheet metal used?

Steel sheets are produced by cold or hot rolling. Hot rolled plates undergo heat treatment. Rolled steel comes off the conveyor in the form of coils or trimmed plates. Hot rolled sheets are divided into thin and thick sheets.

Rolled metal is made from low and alloy carbon steel. Low-alloy sheets are used for assembling welded structures, bridge elements, and pipelines.

Structural rolled steel is used to produce parts intended for industrial and machine mechanisms. Safes and barbecues are very resistant to temperatures and are made from this rolled material.

Hot Rolled Steel Sheet

has heat resistance, quickly welds, and is resistant to corrosion. It is not afraid of mechanical damage, despite simple processing.

Cold rolled sheets are widely used for roofing.

The material is very popular because it has an excellent top layer, is resistant to deformation during welding, and can also be coated with paint without additional processing.

Cold rolled sheets come in different hardnesses, their thickness varies from 0.35 to 5 mm. Plates are made from cold sheet metal:

Perforated;

Galvanized roofing;

Profiled sheeting.

The product is ideal for high-precision structures and is widely used for roofing work.

Corrugated sheets are represented by rolled metal with embossing on the surface. They are usually presented in a diamond shape, but can be made into a "lentil".

They are mainly used for decorative purposes, such as cladding. Galvanized plates have an anti-corrosion coating on one or both sides.

To protect buildings, they are used in cladding, roofing, as well as in the medical and food industries.

The wholesale and retail store has all types of steel sheets

. A convenient ordering and delivery system will appeal to demanding customers, and affordable prices and high quality will turn customers into regular customers.

Steel sheet assortment

Sheet steel is a type of rolled metal produced by hot rolling in rolling mills. It can be used as an independent metal product and as a rolling stock for cold-rolled sheets, production of bent profiles, and pipes. In its production, carbon unalloyed and alloyed steel grades are used.

Range of hot rolled steel sheets

The range of hot-rolled sheet products is regulated by GOST 19903-2015. In accordance with the standard, rolled products are produced in sheets (thickness 0.4-160 mm) or rolls (thickness up to 25 mm). The width of sheets is 500-4400 mm, rolls are 500-2200 mm. Manufacturing accuracy in thickness - increased and normal. Flatness – especially high, high, increased, normal.

This is the most common and popular type of rolled steel in the national economy. It is used in construction, shipbuilding, bridge construction, automobile and aircraft construction, and in the production of locomotive frames.

Table of sheet assortment and weight of hot-rolled steel in accordance with GOST 19903-2015

Range of cold rolled steel sheets

The production of these metal products is regulated by GOSTs 19904-90, 9045-93, 16523-97. Thickness – up to 5.0 mm. Width – 500-2350 mm. Manufacturing accuracy in thickness - high, increased, normal. Flatness – especially high, high, improved, normal.

General-purpose products are made from high-quality carbon steels, and for certain applications - from low-alloy or alloy steels. Such products are characterized by high dimensional accuracy and surface quality, as well as a hardened top layer.

To eliminate work hardening and obtain a fine-grained structure in the surface layer, recrystallization annealing is used.

Cold-rolled sheets are used in the production of profiled sheets, in the automotive industry, in the manufacture of dishes coated with enamel, and containers for canned food products.

Table of dimensions and weight of cold rolled steel sheets

Main characteristics of galvanized sheet

Galvanized sheets are produced by applying a zinc layer to cold-rolled coils or sheets, which protects the base metal from corrosive destruction.

The most common methods of galvanizing in industrial conditions are hot and electrolytic. The main application of such a sheet is the production of corrugated sheets.

It is also used for the manufacture of technological equipment, household appliances, and in the furniture industry.

Galvanized corrugated sheeting: characteristics and areas of application

Profiled sheet is a metal product obtained by profiling cold-rolled galvanized sheets with a thickness of 0.4-1.0 mm on special bending mills. Various grades of this material are used for wall coverings, fencing, and roofing.

Table of sizes and weights of profiled sheets of various brands

Metal profiled sheet with polymer coating: range and main characteristics

To increase the corrosion resistance and decorative characteristics of galvanized corrugated sheeting, it is coated on one or both sides with a colored polymer layer.

Depending on the brand, these products are used for façade cladding, fencing, and as roofing material.

Thanks to the wide range of colors, corrugated sheeting can be selected in accordance with the overall color scheme of the building or the surrounding landscape.

Table of dimensions and weight of polymer-coated corrugated sheets

Corrugated sheet: types and characteristics

Corrugated steel sheet is a popular building material that has a smooth surface on one side and a corrugated surface on the other. The thickness of the main sheet is 2.5-12.0 mm. Produced in accordance with GOST 8568. Products are sold in sheets or rolls. Width – 600-2200 mm. The height of the protrusions is up to 30% of the thickness of the main sheet, but not less than 0.5 mm.

Due to its anti-slip characteristics, corrugated steel sheet is used in the manufacture of steps of stairs, ramps, passages, floors of elevators, cars, and change houses.

Sheets and Rolls

Home \ Sheets and Rolls

Sheet steel is a rolled metal product of small thickness, the edge of which can be cut or uncut. Metal sheet (galvanized, hot-rolled, cold-rolled, etc.) is supplied in rolled or unrolled form

We supply sheet steel for any need:

• For the production of metal structures; • For the manufacture of components for household appliances; • For the production of building profiles, reinforcement, metal frame bases, stiffeners; • For the construction of walls and roofs; • For the production of metal tiles;

The excellent characteristics of the steel sheet allow it to be used for both internal and external work under different operating conditions.

Cold rolled sheets

Hot rolled sheets

Galvanized sheets

Corrugated sheets

Call us to find out your specific price.

1. Complete an online application

2. Send to [email protected] your need

3. Directly contact the manager +7, +7 (925) 357-37-07

WE ARE ALWAYS GLAD TO SEE YOU IN THE RANKS OF OUR PARTNERS!